Видео

i admire your skill, knowledge, nerves and bravery. mad respect mate, thanks for the video.

Are you happy with this Mannol 5w30 7511 engine oil? How many miles do you keep it?

You haven’t removed the any filings that maybe in the sump or removed all the oil from the sump - don’t think the sump pump is really a good way of doing the job - but thanks for the video

I have a same problem , bmw 528i , so it’s the transmission ground strap loose?

Whats the part number?

Thank you for this great Video.

I’ve got a ‘08 CLK 550 with 91k miles on it and it’s a blast to drive, mine is bright red.

Thanks 👍

Did you replace the intake o rings/seals between the manifold and head?

You lucky sod, that job is way more awkward on a discovery 3, due to 2 crossmembers obscuring the bolts at either end

Correct both N57 and B57 are good with those flaps, dont remove them. Just clean whole manifold and put it back

You killer the cp4

hi i have to keep refilling mine every year cost £65.00 l494 2014 3.0 D sdv6... can this be a easy fix please

Any gurus still active here? I just cleaned the whole intake manifold, the swirl flaps and it's still in limp mode. Why is that? None of the swirl flaps are broken or covered in carbon, the sensors are cleared and carbon free, no check engine, no warning lights on the dash, it's idling really nice..I'm clue less.

Lol i broke mine nd other half is stuck inside flash dont know how to get it out😂

How did the painted grilles hold up?

Prop shaft, lol, You must be a boatie/sailor

Since 2009 BMW no longer have swirl flaps and nobody complained about increased fuel consumption.

Similar happened to me. Sacrificed a thin wood chisel to chip off the nut cover then a deep 21mm socket after heating with torch and a ratchet long arm torque wrench.

Since it was a sunny day in South Wales for a change, I took the opportunity to do the egr delete on my 2007 L322 Tdv8 3.6 . All went till I sheared the final torx screw. Luckily this only took an hour to remove. Lesson learned don't overtighten using electric tools 😂. I got the kit from X8R, £££ but good quality.

Where have you gone?

Is there a way to decarb the air intake manifold assembly without taking it apart?

Love this. Great explanation. Very clear.

I've just ordered a new one for my BMW. Issue is, its leaking out of the top where it bolts on to the coolant temperature part. There are no cracks on the part at all. So I can't figure out why it's leaking. The bolts don't need tightening as they won't physically tighten any more than they already are. So I can't figure out why it's leaking from where it is. Nonetheless, I've ordered a new one, very very reluctantly, I may add. This car has been issue after issue.

The alloy plug as an o-ring seal (as you know) so you should have cleaned its seating area prior to fitting (well I would have)

Good video. This car was on sale on ebay was sold and back up at a higher price. I got myself a black coupe 55 AMG last week.

Thanks mate nice video .mines broken and didn’t know if I could attempt it but watchman you now il have a go 🤞🤞👍

Great video, straight to the point 👍😄

28.7 mpg??

I know this is an older video but I'm still going to leave a response. This is one of those ugly jobs that you have to do. I also believe that this was totally necessary. I was watching someone the other day who was doing the math on what percentage of space that brings in the air to the engine and how much of a reduction in it really was. He calculated that he was losing 45% of airflow due to the carbon buildup. I'm hoping to get this done this week. I'm not under the clock so I can take the extra steps and do things while I'm in there. I am fortunate enough to have a shop size air compressor add a walnut gun. I also plan on using my power washer. If the manifold wasn't so expensive to replace I was just order a new one. I did enjoy your video and I made sure to give you a big old thumbs up. I also hit the subscribe button and I'm looking forward to watching more of your videos.

Do you experience any problems with your vehicle when you cancel the flaps?

Just get straight to the point... wtf

Hi I’m hoping that you may has some advice regarding this issue as I have a fault code p115d and engine light that was intermittent but now is permanent and slight loss of power , did you manage to fix the leak if there was a leak regards Josh

What did you do with this in the end?

I have the same sand interior with black piping. I couldn't make out what you said exactly: what color leather repair paint did you get? CR10SUN? Im trying to order a bottle, what size you feel is sufficient for the first row of seats?

Hi, what’s your brake rotor size and rim size?

Bro that hitch is NSFW. Phalic Af

Awesome video! Do those trim pieces pop off the same way for the 2010-2012 l322?

I got my kit from x8r today, cheaper kits are available, to try and fix the rough idle and slow response on my L322 Tdv8 3.6 2007, Fingers crossed. I'll let you know how it goes.

Many thanks fixed also. Came up as a 8040B6 fault in my scanner regarding starter relays etc. I have recently swapped engine and gearbox of a F31 335d following a flood incident. I had done exactly what you did. Managed to test it with a jump lead from engine lifting eye to the chassis negative post and Bingo it worked. Saved me lots of beer vouchers! Well done, nice video.

Oh man, you should have just cleaned up the inlet manifold and not delete!

Really loved the video, I feel confident to do the job myself -Thank you.

How is the car 4 years on?

Very useful video. Can you please let us know where you got the o rings? This would be very useful. Thank you

Just remember, if it's got pistons or tits it's gonna be expensive.

What I learnt from this video was that I'm going to pay someone professional to do my key.

Thank you for posting this video. It helped me a lot.

i love this guy no homo i had the same issue love ya m8!!!!!!

Never start a job if you don't know what your doing , painful to watch

what wad the name of the kit you used for the leather refresh. looks really good.